1/2″ Inch Normally Open Plastic Electric Water Solenoid Valve

WIC Valve 2POG Series 2-way normally open solenoid process valve is to control On/Off of air, inert gas, liquid and vacuum. This solenoid valve has one 1/2″ inch NPT inlet and one 1/2″ inch NPT outlet port. Valve stays open when the coil is de-energized, and it closes when energized. Valve can be mounted in any position.

 

2POG Series Normally Open Plastic Electric Solenoid Valve Specification:

Valve Type: 2 Way Normally Open (Valve closes with energized)

Service Media: Air, Inert Gas, Liquid, Vacuum

Operation Model: Direct Lift Diaphragm

Flow Model: Uni-Directional

Body Material: PA66 Plastic Valve Body

Seal Material: NBR (Buna N) Diaphragm & Plunger Tip

Coil Power: DC – 30W ; AC – 50/60Hz 28VA

Coil Class: H Class IP 65

Coil Duty: 100% ED (Continuous Duty)

Operating Pressure: Vacuum 0 PSI to 90 PSI

Operating Temperature: 0 to 50 °C

Port Size:  1/2″ NPT Female Port

Coil Voltage Option: 12V DC, 24V DC, 24V AC, 110V AC, 220V AC

Low Power Consumption Coil: Upgrade Optional 12V DC – 10W, 24V DC – 7W, 24V AC – 8VA, 110V AC – 8VA, 220V AC – 8VA

Low Power Consumption Coil Inrush Current: 24V DC – 50W, 110V AC – 50/60Hz 85VA, 220V AC – 50/60Hz 154VA

Voltage Tolerances: DC: +10% –5% ; AC: +10% -15%

Electrical Connection: DIN 43650A (PG11) Connector with LED Indicator

 

2POG Series Normally Open PA66 Plastic Electric Solenoid Valve Dimensions (Unit=mm):

Model	Port (NPT)	Flow Rate (Cv)	Orifice Size	A	B	C
2POG-1/2-D	1/2″	4.8	16	68	121	76
2POG-3/4-D	3/4″	7.6	20	68	125	80
2POG-1-D	1″	12	25	82	130	107

 

2POG Series PA 66 Plastic Normally Open Electric Solenoid Valve Component Drawing:

Frequently Asked Questions:

What is PA66 Material?

PA66 (Nylon 66) or Polyamide 66 is an engineering-grade thermoplastic.  PA66 is a semicrystalline-crystalline material which is one of the highest melting points among commercially available polyamides.  The advantage of the PA66 is that it has a high mechanical strength and good stability under heat.

 

What is DIN Connector?

Instead of using the Grommet lead wires, the coil has the prongs or pins to connect a standard DIN connector. Therefore, the coil will have a male connection and the plug connecting to the coil is a female connector. The DIN connector for this 2POG series valve is a DIN 43650A 18mm (PG11) type. The advantages of the DIN Connector is that it allows a quick valve or coil exchange. Yet it is a excellent insulation properties and good for water tightness.

 

How to connect DIN connector with wire?

To connect the wire to DIN connector is simple and easy, shown below is the 4 easy steps:

1. Remove the Philip screw from the plastic housing protector.

2. Unplug the plastic housing from the DIN coil.

3. Remove the terminal block from the plastic housing.  Use the Philip screw to push the terminal block out from the plastic housing.

4. On the back of the terminal block, it makes 1, 2 and Ground. For the DC DIN coil, connect 1 to positive, and 2 to negative. For the AC DIN coil, connect 1 to Hot wire, 2 to Neutral wire, and Ground to Ground wire if required.

What is ED 100% Coil Duty?

ED 100% indicates suitability of the coil to operate in “continuous service”, in other words it is good for constantly energised.